8Ch 433.92M EV1527 Learning Code OOK ASK RC Multi-function Remote Control Module DC 5V 12V 24V

1. Operating Voltage : DC 12V(5V optional) ​

2. Operating Current(DC 12V) : Standby current 11MA, 1 relay open 37MA, 2 relays open 64MA, 3 relays open 88MA, 4 relays open 110MA, 5 relays open 131MA, 6 relays open 151MA, 7 relays open 170MA, 8 relays open 187MA ​

3. ''Momentary'' ''Self-locking'' ''Interlock'' ''Delay'' Four functional modes 

​4. Decoding type: fixed code, can be adapted to up to 32 remote controls 

​5. Remote control type: EV1527compatible ​

6. Working distance: 100 meters (Wireless reception sensitivity: -108dbm) ​

7. Input control pins 8 ,5V TTL level ,NPN trigger, 0.2-2 second low pulse ​

8. Size: 99 x 62 x 20 mm 

​9. Weight : 118.6g ​

10. Relay maximum load capacity: DC 1-110V/5A; AC 85-265V/6A

Power supply : 12V 23A battery replacable .(This remote doesnot have a battery , Please buy in your local market ) ​

Operating current: ≤ 18mA ; ​

Oscillation mode: SAW resonator ; ​

Oscillation resistor : 270K ​

Modulation mode: ASK OOK ; ​

Operating frequency: 433.92MHz ; ​

Frequency dev iation: ±0.2MHz ; ​

Encoding format: Million Group Code ( EV1527 ) ; 

​Transmit power: 15 mW. ​Data Rate : 50~60KHZ;​ ​ ​

8 channel Multi-function 433M Wireless controller, each channel independently triggered independent delay, do not interfere with each other. 

4 kinds of Functional mode: Non-locking (Momentary );Delay(2/10/60/600/3600seconds); Self-locking (Toggle); Inter-lock (Latch), The function mode and delay time are selected by the Solder pad. 

​Low pulse trigger(Connect to the power supply GND via the trigger button or low level control via the MCU IO port)

 

Function mode selection by shorting three pads M2 1 0:

In normal working mode, the LED will be always on, and when a valid remote control key value is received, the LED will flash. ​

Clear code: Press and hold the button, and the LED will be off. After about 5 seconds, the LED will be on, and the code clearing is completed (Note: After the clear code is executed, the previously saved remote control does not exist. If you need to use the old remote control, please re-learn). ​ ​

Adaptation (learning):​

Step 1 (matching the remote control): Press any button on the remote control, if the LED light flashes quickly, it means it is a matching remote control, otherwise it is not a matching remote control. ​

Step 2 (enter learning mode): touch the button, the LED light is off. ​

Step 3 (Learning the remote control): Press any button on the remote control within 10 seconds, the LED light flashes 3 times and then turns on, then the learning is successful; if the LED light only flashes twice, the learning fails, indicating that the learning has been completed pass the remote control; learning is complete. 

​Note: Please use the remote control we sell, otherwise it may not be compatible with the remote control. ​ ​ ​

Wiring diagram:​1 DC 12V(5V/24V) control circuit,Wiring diagram below. ''LOAD'' may be LED lights, fans, toy car and other DC 12V(5V/24V) equipment ​

2 DC 1-100V OR AC 85-265V control circuit,Wiring diagram below. ''LOAD'' may be LED lights, fans, motors and other DC AC equipment