Module Board

Feature:Free TutorialGood kit for Arduino Starter17 Classes:Class 1 Hello Arduino!Class 2 LED Running LightsClass 3 Key ExperimentClass 4 AD  Analog-to-Digital conversationClass 5 PWM ExperimentClass 6 Buzzer ExperimentClass 7 The Temperature Sensor ExperimentClass 8 Photosensitive Light ExperimentC..

Parameter:Supply voltage: DC 7~28VSensor excitation voltage: DC 5VInput signal range: ±20mvSampling rate: 10 times per secondAD precision: 24 bitsResolution: >50000 divisionsInstallation method: fixed with mounting holesInterface form: RS485Communication protocol: standard Modbus-Rtu protocol, suppo..

>>>Manual: Contact Us<<<Principle:The QRM canceller is inserted into the feeder of the antenna from thetrx without any other modifications to the radio. The box has a built-in PTT control to keep the canceller connected during transmission. However, an additional auxiliary rec..

Feature:1. Complete 802.1 1b/g/n WIFI SOC module2. Built-in Tensilica L106 ultra-low power consumption 32-bit micro MCU, main frequency supports 80 MHz and 160 MHz, supports RTOS3. Support GPI0/PWM interface4. Built-in Flash5. Adopt DIP-16 package6. Integrated Wi-Fi MAC/BB/RF/PA/LNA7. Support multip..

Description:  Press and hold the flash and RST buttons simultaneously to program the firmware. Size: 40 x 28mm Fixed distance: 3mm Hole spacing: 1400 x 900mil (35.56 x 22.86mm) Voltage: 5V Frequency range: 2.4G-2.5G Flash capacity: 4MB Package Included: ..

Feature:ESP32 integrates antenna switches, RF balun, power amplifiers, low noise amplifiers, filters and power management modules, and the entire solution occupies the smallest printed circuit board area. 2.4 GHz Wi-Fi and Bluetooth dual-mode chipUsing TSMC low-power 40nm technology, the power perfo..

Description:This is the ESP - 32 s wireless module adapter plate. It can use the dupont cable inserted into the bread plate. For development and debugging.2.54mm pitch, lead to RESET and IO 0 ports, can be inserted into breadboard, use Dupont wire leads, etc., to facilitate development and debugging..

Note: Due to different batches, the actual chips will be different. ESP-WROOM-32 and ESP-WROOM-32D will be shipped randomly.Feature:ESP32 integrates antenna switches, RF balun, power amplifiers, low noise amplifiers, filters and power management modules, and the entire solution occupies the smallest..

Description:The ESP-C3-12F-Kit development board is a core development board designed by ESP-C3-12F for the ESP-C3-12F module. The development board continues the classic design of the NodeMCU development board, leading all I/O to the With pin headers, developers can connect peripherals according to..

Package includes:1 x ESP32 0.96 OLED 1 x HX711 Module 1 x 1KG Weight Sensor 2 x Bracket 1 x Cable 1 x Screws (bag)Wiring:..

Note: OLED is not soldered to T-BEAMIf you need additional OLED, you can buy it from: Product ID:958196/Product ID:969144 Product Upgrade Content: 1. Pin GPIO34 pin is replaced with GPIO35 2. Replace the charging IC (TP5400) with the power management AXP192 3. GPS TX, RX..

Feature:ESP32-C3 is a low-cost microcontroller from Espressif that supports 2.4 GHz Wi-Fi and Bluetooth® Low Energy ( Bluetooth 5 (LE)).Use RISC V as the core.There's a minimum number of pins on this chip, it's specifically designed to be low cost and for simpler projects than ESP32-Sx or ESP32 clas..